Showing results: 1441 - 1455 of 2716 items found.
-
N844-LOOP-12F -
Tripp Lite
Tripp Lite N844-LOOP-12F MTP / MPO OM3 Fiber Optic Loopback Tester is typically used for test and measurement procedures in networking environments. The device is ideal for a multitude of applications that require signal looping in a MTP / MPO form factor. Features push-pull tab for easy disconnect. A dust cap is included for protection during storage.
-
CSM Products, Inc.
For high-speed measurement applications exceeding the CAN bus capabilities, CSM's EtherCAT®-based MiniModules provide the optimal solution. EtherCAT® is an established protocol for fast and synchronous measurements with its roots in the test bench measurement technology sector. It has high bandwidth capability, maximum number of measurement channels, and precise synchronization of measurement signals.
-
EMX-1434 -
AMETEK VTI Instruments
* 4-Channel, 204.8 Ksa/s per channel, 24-Bit DACs* -115 dB spurious free dynamic range* Integrated 2-Channel 64-bit tachometer* Integrated 4-Channel DIO* Tight synchronization with DSA analyzers* Ideal for rotational measurement, and stimulus-response applications such as vibration test* Output modes including Sine, Burst Sine, Chirp, Burst-random and continuous random
-
783588-01 -
NI
PXIe, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis—The PXIe‑1085 features a high-bandwidth, all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
781813-01 -
NI
PXIe, 18-Slot (16 Hybrid Slots, 1 PXIe Timing Slot), Up to 24 GB/s PXI Chassis—The PXIe‑1085 features a high-bandwidth, all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
34908A -
Keysight Technologies
Use the Keysight 34908A module for the 34970A/34972A Data Acquisition/Switch Unit for the greatest density in common-low applications, such as battery test, component characterization, and benchtop testing. Each module switches 40 one-wire inputs. All two-wire internal measurements except current are supported. The module low connection is isolated from earth and can float up to 300 V.
-
40-298-010 -
Pickering Interfaces Ltd.
The 40-298-010 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
LTP-250A -
Lambient Technologies
Test labs and university researchers need reliable, robust solutions for applying heat and pressure to samples. But standard industrial presses are too powerful and costly, and can take up too much space. Organizations responsible for small parts molding applications and composite materials development and testing need press solutions optimized for their specific materials and testing environments.
-
Signal Processing - DX -
APEX Turbine Testing Technologies
DX is an easy to use, graphical, signal processing environment that simplifies analysis and reporting of dynamic data. DX includes everything needed to process data for a variety of applications and industries in a very intuitive, drag-and-drop user interface. Generate fully-interactive engineering plots from one or more tests and create reports in just a few mouse clicks.
-
SERIES 6000 MULTIMODE -
Polatis, Inc.
The Series 6000 Multimode switch is designed to meet the needs of the most demanding component, subsystem and system test applications. All-optical switching allows test equipment connections to be fully automated and controlled remotely 24/7 via software from virtually anywhere in the world.
-
MASER Engineering B.V.
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
Rhopoint Metrology Ltd
1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in its box or in a dust free area.5. When using a dial test indicator, always position the dial test indicator in a horizontal plane to the surface media.6. Always use a rigid stand for mounting the dial test indicator.7. When measuring a rotating object, either between centres or in a vee block, ensure that the object is rotating in the correct direction. Never rotate the workpiece towards the contact point.8. When measuring a sliding object, only take readings when the object is moving directly towards the contact point, never away from the contact point or in a sideways manner.9. Avoid parallax errors by reading the dial directly from the front and square on to the dial.10. Never oil a dial test indicator as this attracts contamination, should the movement become erratic then the dial test indicator should be submitted to a reputable repair agent.11. Try not to expose dial test indicators to direct sunlight or in a high humidity environment.12. Never use a dial test indicator that has not been calibrated, if in doubt consult an appropriate authority.
-
Triplett Test Equipment & Tools
compact digital multimeter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Voltage, DC Current, Resistance, Continuity, Diode Test, Transistor hFE, and Temperature. The rubberized boot provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. The Model 1101-B is well suited for a variety of commercial and residential applications such as security, home theater, electrical, HVAC installations and more. Includes test leads with alligator clips, Type K bead probe and battery (9V).
-
T3PS Series -
Teledyne LeCroy
The Teledyne Test Tools range of DC Bench Power Supplies comes in non-programmable and programmable versions with one, two, three and four output configurations. Key features within the Teledyne Test Tool Power Supply range include programmability via USB or LAN, a graphical display of power waveforms, as well as high resolution numeric display of voltage and current. Typical customer applications for DC Bench Power Supplies include those in industries such as mobile, automotive, communications, defense, and manufacturing as well as those within teaching, education and research institutions.
-
FS-ATG -
Flynn Systems Corp.
FS-ATG is the world's easiest ATG program - pull-down menus, online help, and test generation wizard guide new users step-by-step through the process. It takes less than 2 minutes to 'point & click' a setup program for a board full of devices.Generates Vectors Faster Than EverFS-ATG is a 32-bit Windows 98/NT/2000 application that takes full advantage of today's powerful PC's. Small devices finish in seconds and most FPGAs / CPLDs, even the largest and most complex, can develop great tests after in just a few hours.
